Guide · Homeowners · 4 min read · Updated 17 November 2026
Cracks in Brick Walls: Causes, When to Worry and How They Are Fixed
Short answer
Cracks in brick walls are caused by movement, such as subsidence, heave, tree roots, leaking drains, thermal expansion, failed lintels or rusting wall ties. Hairline cracks under 1mm are often cosmetic. Stepped cracks through mortar joints, cracks wider than about 5mm, or cracks that keep growing need investigating, and serious or ongoing movement should be assessed by a structural engineer before repairs such as crack stitching.
Common causes of cracks
Brickwork cracks when it is asked to move more than it can. The cause matters, because a repair that ignores the cause will usually crack again. Some movement is small and seasonal, while some is a sign of a bigger problem below ground or inside the wall.
Shrinkable clay soils, especially near trees, swell in wet winters and shrink in dry summers, which can make walls rise and fall. Leaking drains can wash away fine soil under foundations. Long walls without movement joints crack from thermal expansion. Lintels over windows and doors can rust or sag, causing cracks from the corners of openings.
| Cause | Typical crack pattern | Common setting |
|---|---|---|
| Subsidence or heave | Stepped or diagonal, often wider at one end | Clay soils, near trees or leaking drains |
| Failed lintel | From the corners of openings | Older windows and doors |
| Wall tie corrosion | Horizontal cracks at regular intervals | Older cavity walls |
| Thermal movement | Vertical cracks in long runs | Garden walls, long elevations |
| Frost damage | Spalling faces, crumbling joints | Exposed walls, poor coping |
How serious is the crack
Engineers often classify crack damage by width, using a scale from the Building Research Establishment. Very fine cracks are usually cosmetic and can be filled during decoration. Wider cracks need more repair, and the widest may indicate structural damage needing significant work. Width is only part of the picture: a crack that is growing matters more than a wide crack that has been stable for years.
A simple way to monitor is to mark the ends of the crack in pencil, note the date and measure the width at a fixed point. Tell-tale crack monitors, which slide apart if the crack moves, are inexpensive and more accurate.
- Under about 1mm: usually cosmetic, fill and monitor.
- About 1mm to 5mm: repoint or repair; check the cause.
- Over about 5mm, or growing: get a structural engineer to assess.
- Doors or windows sticking, or cracks inside too: get it assessed.
When to call a structural engineer
Call a structural engineer if a crack is wider than about 5mm, is growing, appears suddenly, runs through bricks rather than just mortar, or is accompanied by doors and windows sticking, floors sloping or cracks inside. An engineer can identify the cause, decide whether the movement is historic or ongoing, and specify a repair. If subsidence is suspected, contact your buildings insurer early, as many policies cover it and insurers usually want to manage the investigation.
Once the cause has been dealt with, such as a drain repaired or a tree managed, a bricklaying contractor can carry out the specified repairs.
How cracks are repaired
Crack stitching is the most common repair for stable cracks in brickwork. The contractor cuts slots into horizontal mortar joints across the crack, usually every few courses, and beds stainless steel helical bars into them with a grout. The crack itself is filled and the joints repointed to match. This ties the wall back together and spreads stress, typically costing £80–£150 per metre.
Other repairs depend on the cause. Failed lintels are replaced, and the brickwork above is rebuilt. Rusting wall ties are replaced with remedial ties fixed through the outer leaf. Badly cracked or bulging sections may need taking down and rebuilding, using matched bricks and mortar. Where foundations themselves have failed, underpinning may be needed, which is specialist work designed by an engineer and usually approved by building control.
Cracked bricks are cut out and replaced individually, with new or reclaimed bricks matched for size, colour and texture. The mortar used for the repair should suit the wall, which means lime on older buildings.
Preventing new cracks
Many cracks can be avoided with good maintenance. Keep gutters and downpipes clear so water does not pour down walls or soak into the ground at the foundations. Get leaking drains repaired quickly. Think carefully before planting thirsty trees close to the house, and get advice before removing large trees on clay soils, as this can cause heave.
Use the right mortar for the bricks and repoint before joints fail completely. On long garden walls, make sure movement joints are included and copings are sound.
- Keep gutters, downpipes and drains in good order.
- Manage trees and shrubs near the house.
- Repoint before joints fail completely.
- Include movement joints on long walls.
Cracks in garden and boundary walls
Free-standing garden walls crack for slightly different reasons from house walls. Shallow foundations move with the ground, roots from hedges and trees lift and push the base, and long runs without movement joints crack vertically from expansion. Walls holding back soil, often unintentionally after garden levels have been raised, are pushed outwards and may lean or bulge.
A leaning or bulging garden wall can be dangerous, especially next to a pavement or where children play. If a wall has moved noticeably out of plumb, keep people away from it and get it checked. Often the best answer is to take down the affected section and rebuild it on a proper foundation, with movement joints and a sound coping, rather than patch it.
Small, stable cracks in garden walls can usually be repointed or stitched. Rebuilding a section of a one-metre-high wall is typically priced per metre, similar to a new wall, at around £180–£350 per metre depending on bricks and foundations.
Questions people also ask
Are hairline cracks in brickwork normal?
Fine hairline cracks under about 1mm are common in brickwork and are often caused by minor shrinkage or thermal movement. They are usually cosmetic and can be filled or repointed. Monitor them, and get advice if they widen, lengthen, appear inside or are joined by sticking doors and windows.
What is crack stitching?
Crack stitching is a repair for stable cracks in brickwork. Stainless steel helical bars are grouted into slots cut in the mortar joints across the crack, tying the wall back together. The crack is then filled and repointed to match. It typically costs £80–£150 per metre in the UK.
Do horizontal cracks mean wall tie failure?
Horizontal cracks appearing at regular intervals in an older cavity wall can be a sign of corroding wall ties, which expand as they rust and push the brickwork apart. A surveyor or specialist can confirm by inspecting ties with a small camera or by removing a brick. Remedial ties can then be installed.
Written and checked by the Bricklaying Contractors team. Read our editorial policy.
More guides
How Much Does a Bricklayer Cost in the UK? 2026 Prices
A skilled bricklayer in the UK typically costs £220–£320 per day in 2026, with labourers and materials on top. Priced by the job, a one-metre-high…
How a Brick Garden Wall Is Built: Foundations, DPC and Coping
A well-built brick garden wall sits on a concrete strip foundation dug below frost depth, typically at least 450mm and deeper on clay or near trees.…
Repointing Brickwork: When It Is Needed and Lime vs Cement
Brickwork needs repointing when mortar joints are crumbling, recessed or missing, letting water into the wall. Good repointing rakes the old mortar…
Party Wall Act and Brickwork: When You Need to Notify Neighbours
In England and Wales, the Party Wall etc. Act 1996 requires you to give your neighbour written notice before building a new wall on or astride the…
Get a free bricklaying contractors quote
Tell us what you need and we'll come back with a clear price.
Request a quote