Guide · Homeowners · 4 min read · Updated 17 November 2026
Repointing Brickwork: When It Is Needed and Lime vs Cement
Short answer
Brickwork needs repointing when mortar joints are crumbling, recessed or missing, letting water into the wall. Good repointing rakes the old mortar out to around twice the joint width, then refills with a mortar softer than the bricks, which means lime mortar for most pre-1919 buildings and a suitable cement mix for modern brick. It typically costs £40–£80 per m², plus scaffolding for upper floors.
Signs your brickwork needs repointing
Mortar is meant to wear more quickly than the bricks around it. Over decades, rain, frost and wind erode the joints until they are recessed, cracked or missing. When that happens, water gets deeper into the wall, which can lead to damp inside, frost damage to the bricks and loose brickwork.
Not every wall needs full repointing. Often only the most exposed areas, such as chimneys, parapets, garden walls and the weather side of the house, need attention. Spot repointing of damaged areas is common and cheaper.
- Mortar crumbles when scratched with a key.
- Joints recessed more than a few millimetres.
- Gaps, cracks or missing mortar.
- Damp patches inside behind the affected wall.
- Plants growing out of the joints.
Lime or cement mortar
The choice of mortar is the most important decision in repointing. Most buildings put up before around 1919 were built with soft bricks and lime mortar. Lime is softer and more breathable than cement, so moisture in the wall can escape through the joints. If an old wall is repointed in hard cement, moisture is trapped in the bricks instead. Frost then damages the brick faces, which crumble and spall while the cement joints stand proud.
Modern houses with hard, dense bricks are usually built with cement-based mortar, and repointing them in a suitable cement and lime or cement and sand mix is normal. The rule is that the mortar should always be weaker and more permeable than the bricks, so that the joints, not the bricks, take the wear.
| Factor | Lime mortar | Cement mortar |
|---|---|---|
| Typical use | Pre-1919 and soft brick buildings | Modern, hard brick buildings |
| Breathability | High | Low |
| Flexibility | Accommodates slight movement | Rigid, more prone to cracking |
| Curing | Slow, needs protection from frost, sun and rain | Faster |
| Cost | Higher materials and labour | Lower |
How repointing should be done
The old mortar is raked out to a consistent depth, usually around twice the height of the joint and to sound mortar behind, without damaging the brick edges. On old brickwork, this is often done carefully with hand tools, as angle grinders can easily chip the arrises and widen joints. The joints are brushed out and dampened so the new mortar does not dry too quickly.
New mortar is pressed in firmly in layers, then finished to the chosen profile once it has stiffened. Lime work is protected from strong sun, rain and frost with hessian or sheeting for several days. Repointing is best done between spring and autumn, when frost is unlikely.
Joint profiles
The finish of the joint changes how the wall looks and how well it sheds water. On older buildings, the aim is to match the original joint, which is often flush or slightly recessed. Modern houses commonly have bucket-handle or weathered joints.
- Flush: mortar level with the brick face, common on older work.
- Bucket-handle: a shallow curved recess, sheds water well.
- Weathered: angled to throw water off, good for exposed walls.
- Recessed: crisp shadow lines but can hold water on exposed walls.
- Ribbon or strap pointing: proud of the face, best avoided on old brickwork.
Costs and timescales
Repointing typically costs £40–£80 per m², depending on the joint width, the condition of the existing mortar, the mortar type and the pattern of brickwork. Lime work and fine joints are at the upper end. Scaffolding for upper floors and chimneys is usually extra and can be a significant part of the total.
A two-person team can typically repoint a few square metres to around ten square metres a day, depending on the condition of the wall and the joint style. A full front elevation on a terraced house might take one to two weeks, including scaffolding up and down.
Listed buildings and conservation areas
Listed buildings need listed building consent for alterations that affect their character, which can include repointing in a different mortar or joint style. Councils will usually expect lime mortar matched in colour and texture to the original. Conservation areas may also have guidance on repointing. Check with your council before starting, and choose a contractor experienced with lime.
Common repointing mistakes
The most damaging mistake is using hard cement mortar on soft, old brickwork. It looks fine at first, but within a few winters the brick faces start to crumble around the joints. Removing that cement later is slow, and the damaged bricks may need cutting out and replacing, which costs far more than doing the pointing properly in the first place.
Other common problems include raking out too shallow, so the new mortar falls out, widening joints by grinding into the brick edges, smearing mortar over the brick faces, and working in frost or hot sun so the mortar fails to cure. Poor colour matching is another, leaving a patchwork appearance. Asking to see a test panel before the whole wall is done lets you check colour, texture and joint style.
Ask the contractor which mortar they will use and why, how deep they will rake out, what tools they will use on old brickwork, and how the work will be protected while it cures.
- Cement mortar on soft, old bricks.
- Shallow raking out.
- Grinders damaging brick edges.
- Mortar smeared on brick faces.
- Working in frost or strong sun.
Questions people also ask
How do I know if my house needs lime mortar?
If your house was built before around 1919, has soft, handmade or older bricks, or has no cavity in the walls, it was very likely built in lime mortar and should be repointed in lime. Modern houses with hard bricks are usually suited to cement-based mortar. A contractor can test the existing mortar to confirm.
Can I repoint over the old mortar?
No. Spreading new mortar over old joints without raking them out does not bond well and soon falls away. Old mortar should be raked back to sound material, usually around twice the joint height, before repointing. This gives the new mortar enough depth to grip and seal the joint.
How long does repointing last?
Good repointing can last 30 years or more, depending on exposure, mortar type and workmanship. Lime pointing on older buildings is designed to wear slowly and sacrificially, protecting the bricks. Exposed walls, chimneys and garden walls usually need repointing more often than sheltered elevations.
Written and checked by the Bricklaying Contractors team. Read our editorial policy.
More guides
How Much Does a Bricklayer Cost in the UK? 2026 Prices
A skilled bricklayer in the UK typically costs £220–£320 per day in 2026, with labourers and materials on top. Priced by the job, a one-metre-high…
How a Brick Garden Wall Is Built: Foundations, DPC and Coping
A well-built brick garden wall sits on a concrete strip foundation dug below frost depth, typically at least 450mm and deeper on clay or near trees.…
Party Wall Act and Brickwork: When You Need to Notify Neighbours
In England and Wales, the Party Wall etc. Act 1996 requires you to give your neighbour written notice before building a new wall on or astride the…
Cracks in Brick Walls: Causes, When to Worry and How They Are Fixed
Cracks in brick walls are caused by movement, such as subsidence, heave, tree roots, leaking drains, thermal expansion, failed lintels or rusting…
Get a free bricklaying contractors quote
Tell us what you need and we'll come back with a clear price.
Request a quote