Guide · Homeowners · 4 min read · Updated 17 November 2026
How a Brick Garden Wall Is Built: Foundations, DPC and Coping
Short answer
A well-built brick garden wall sits on a concrete strip foundation dug below frost depth, typically at least 450mm and deeper on clay or near trees. It uses frost-resistant bricks, a damp-proof course just above ground, piers or a thicker wall for strength, movement joints on long runs, and a coping that throws water clear. Walls are usually limited to 2m high, or 1m next to a highway, without planning permission.
Why garden walls fail
Garden walls take more punishment than house walls. They are exposed to rain on both faces and the top, they freeze and thaw through the winter, and they often have soil, roots or a hedge pushing against them. Most failures come from a few causes: shallow foundations that move with the ground, bricks that are not frost-resistant, no proper coping, and walls that are too thin for their height.
A wall built to last uses the right materials for exposure and has enough foundation, thickness and support to stay upright for decades.
Foundations
Most garden walls sit on a concrete strip foundation. It should be deep enough to reach firm ground below the level where frost and seasonal shrinkage affect the soil. That is typically at least 450mm on firm ground, and deeper on shrinkable clay or near trees and large shrubs, whose roots dry and move the soil. The strip is usually two to three times the width of the wall.
The trench is dug, the bottom checked for soft spots, then concrete is poured and levelled. Once it has set, the first courses below ground are often built in engineering bricks or dense blocks, which resist water and frost better than facing bricks.
- Dig to firm ground below frost depth.
- Go deeper on clay or near trees.
- Make the strip two to three times the wall width.
- Use engineering bricks or dense blocks below ground.
Wall thickness and piers
Garden walls are built either half a brick thick, around 102.5mm, or one brick thick, around 215mm. Half-brick walls are cheaper but need piers, thicker brick columns built into the wall at intervals, to stop them blowing over. One-brick walls are much stronger, look more solid and suit taller or longer walls. The right choice depends on height, length, exposure and whether the wall holds back soil.
Any wall holding back soil is a retaining wall and needs a different design, often with thicker construction, reinforcement and drainage behind it. Taller retaining walls should be designed by an engineer.
| Wall type | Thickness | Typical use |
|---|---|---|
| Half-brick with piers | Around 102.5mm | Low garden walls, planters |
| One-brick | Around 215mm | Boundary walls, taller walls, front walls |
| Cavity or reinforced | Varies | Retaining walls, higher or exposed walls |
Bricks, mortar and DPC
Garden walls should be built in bricks rated for severe exposure, as they are wet from both sides and the top. Frost-resistant facing bricks for the visible courses, with engineering bricks below ground, is the usual combination. If the wall is close to the house, matching the house bricks keeps it looking right.
The mortar should suit the bricks and exposure, typically a stronger mix below ground and a suitable general-purpose mix above. A damp-proof course, often two courses of engineering brick or a DPC membrane, is laid just above ground level to stop moisture rising into the wall. Long walls need movement joints so the brickwork can expand and contract without cracking.
Copings and finishing
The top of the wall needs protection. A coping or capping stops rain soaking down into the brickwork, which is a common cause of frost damage and staining. Options include brick-on-edge, purpose-made coping bricks, stone or concrete copings. The best copings overhang slightly and have a drip groove underneath, throwing water clear of the wall face.
Joint finish matters too. A bucket-handle or weathered joint sheds water well and suits most garden walls. Raked or recessed joints look sharp but can hold water on exposed walls.
- Coping with overhang and drip groove.
- DPC course under the coping on exposed walls.
- Weather-shedding joint profile.
- Movement joints on long runs.
Height and planning rules
Under permitted development, garden walls are normally limited to 2 metres high, or 1 metre next to a highway, without planning permission. Higher walls, walls at listed buildings and walls in some conservation areas need permission. If the wall is on the boundary line with a neighbour, the Party Wall etc. Act 1996 may apply in England and Wales, and you may need to serve notice before work starts.
A specialist contractor can advise on all of this and give a fixed price per metre, typically £180–£350 per metre for a one-metre-high wall including foundations, bricks, DPC and coping.
What happens on a typical job
Most garden walls follow the same sequence. On day one, the old wall is taken down if there is one, the line is set out with string and pegs, and the foundation trench is dug and checked. The concrete is poured and left to harden, usually at least overnight and often longer in cold weather. Below-ground courses and the damp-proof course go in next, then the visible brickwork rises course by course, with the line checked for level and plumb as it goes.
Finally, the coping is bedded, joints are finished and the site is cleaned up. A 10m wall one metre high is often built in three to five working days, weather permitting. Bricklaying stops in frost or heavy rain, as fresh mortar is easily damaged, and new work is covered at the end of each day.
Before work starts, clear plants and furniture from a working strip of about a metre on your side, agree where materials will be stored and check that the wall line is where you want it. If the wall is on the boundary, make sure any party wall notice has been dealt with.
- Demolition and set-out.
- Foundation trench and concrete.
- Below-ground courses and DPC.
- Facing brickwork, piers and openings.
- Coping, joint finishing and clean-up.
Questions people also ask
How deep should a garden wall foundation be?
A garden wall foundation should reach firm ground below frost depth, typically at least 450mm, and deeper on shrinkable clay or near trees. The concrete strip is usually two to three times as wide as the wall. Taller walls and retaining walls need deeper or engineer-designed foundations.
Does a garden wall need a damp-proof course?
Yes, most brick garden walls should have a damp-proof course just above ground level, often two courses of engineering brick or a DPC membrane. It stops moisture rising into the facing bricks, reducing frost damage and staining. Exposed walls may also have a DPC beneath the coping.
Should a garden wall be one or two bricks thick?
Low garden walls can be half a brick thick with piers for support. Taller, longer or more exposed walls are usually built one brick thick, around 215mm, which is stronger and more stable. Retaining walls need their own design and may need an engineer.
Written and checked by the Bricklaying Contractors team. Read our editorial policy.
More guides
How Much Does a Bricklayer Cost in the UK? 2026 Prices
A skilled bricklayer in the UK typically costs £220–£320 per day in 2026, with labourers and materials on top. Priced by the job, a one-metre-high…
Repointing Brickwork: When It Is Needed and Lime vs Cement
Brickwork needs repointing when mortar joints are crumbling, recessed or missing, letting water into the wall. Good repointing rakes the old mortar…
Party Wall Act and Brickwork: When You Need to Notify Neighbours
In England and Wales, the Party Wall etc. Act 1996 requires you to give your neighbour written notice before building a new wall on or astride the…
Cracks in Brick Walls: Causes, When to Worry and How They Are Fixed
Cracks in brick walls are caused by movement, such as subsidence, heave, tree roots, leaking drains, thermal expansion, failed lintels or rusting…
Get a free bricklaying contractors quote
Tell us what you need and we'll come back with a clear price.
Request a quote